Fire Alarm Annunciator Model 5235 User Manual

Advertising

Supplement to the MS-9600(UD)LS(C/E) Fire-Lite Manual Document 52646 Revision B 53587 Supplement to the SWIFT Wireless Manual Document LS10036-000FL-E Revision B dated 9/14/2015. Fire-Lite B310LP Installation Instructions. Smoke Alarm Fire-Lite 1451 User Manual. MODEL RA400Z Connect the remote annunciator between terminals 1 and 3 using.

PFC-4410RC • 5403550 • REV Q • 11/12

Lamp Test

When the panel is in a Normal Condition, pushing the two top buttons will illuminate all of the LED's and display for

approximately one second.

Remote Annunciator Model RA-4410RC Operation

Red LED’s:

Initiating Device Circuits Active (4)

Notification/Release Circuits Active (4)

Common Alarm (1)

Green LED’s: AC Power

Yellow LED’s: Initiating Device Circuits troubles (4)

Output Circuit Troubles (4)

Supervisory Initiating Zone (4)

Supervisory Bell Output Active (4)

(1) each: Sup 1/Abort, Supervisory 2, Power Trouble,

Supervisory Trouble, System Trouble, Ground Fault,

Pre-Discharge/Discharging, Alarm Silenced

The appropriate LED flashes to indicate a change of status on the panel. A trouble or supervisory condition will flash the appropriate

Yellow LED indicating the location of the condition. If any outputs are programmed as TROUBLE or SUPERVISORY BELL, that

Yellow output LED will flash indicating the output is activated. Pressing the BUZZER SILENCE button on the panel changes the

flashing zone Amber LED to steady on and turns the flashing Yellow output LED off.

An alarm condition will flash a Red LED indicating the zone in alarm and any outputs mapped to that zone that have activated.

Pressing the SIGNAL SILENCE button changes the flashing Red Zone LED to steady on and the flashing Red Output LED mapped

to that zone off unless the output is programmed as RELEASE. In addition, the Yellow ALARM/ SILENCE LED will light.

Any zone programmed as WATERFLOW is considered non-silenceable so the signal and buzzer silence buttons will have no

effect on the flashing zone and output LED's. A buzzer on the annunciator sounds for any trouble condition. When the panel

has a trouble or supervisory condition, pressing the SILENCE/LAMP TEST button silences the condition at the panel and all

Wireless Earbuds User Manual Thank you for purchasing our products. This manual addresses the safety guidelines, warranty and operating instructions. Please review this manual thoroughly before operating your device. SAFETY AND WARRANTY Important Safety Instructions Use of earbuds will impair your ability to hear other sounds. BS121FE TRUE WIRELESS EARBUDS User Manual TRUE WIRELESS EARBUDS should be used with the compatible devices which support Bluetooth wireless technology. This allows you to make two calls and enjoy the music streaming at any time freely. Please read this user manual carefully before using the EARBUDS, and also read your device’s user manual regarding. Soundmoov is an audio products and electronic innovator. We look beyond just building one of the best true wireless earbuds. Through the insightful application of the latest technology, we create innovative audio solutions that help solve the problems that prevent people from getting their most important tasks done. Soundmoov, hear what moves you! 1.Tap the button on both earbuds at the same time. You will hear “Power on” and then saying, “Your device is connected”. 2.Find HV-316T on your phone or tablet wireless list. Click it and you will hear “Your device is connected”. SoundMates-Wireless Stereo Earbuds User Manual details for FCC ID 2AE3CBE4001 made by KINLAN INDUSTRIAL LIMITED. Document Includes User Manual Soundmates Manual - KINLAN. Soundmoov wireless earbuds pdf user manual for samsung note 4.

annunciators. When no non-silenced trouble or supervisory conditions exist, pressing the SILENCE/LAMP TEST button can be

used to test the LED's.

The release panel supervises and communicates with the annunciator via separate connections for the RS-485 communication and

24VDC power requirements of the RA-4410RC. Separate cables should be used for power and communication. Shielded cable

shall be used for the communication line. Up to four annunciators can be connected to one panel. A rotary switch is provided on

the panel to indicate how many annunciators are connected. Another rotary switch is on the annunciator to set the address. The

annunciators must be addressed consecutively. See page 89 for wiring information. Refer to bulletin #8840024 for installation

instructions and maximum wire run.

Test Procedure

The system should be inspected, tested and maintained in accordance with NFPA-72 National Fire Alarm Code, Chapter 10 and

any other requirements of the local authority having jurisdiction.

Test Procedure (Canada)

The system should be inspected, tested and maintained in accordance with ULC Standard CAN/ULC-S536 and any other

How can we think of life in its dual expression, matter and experience, the living and the lived? Philosophers and, more recently, social scientists have offered multiple answers to this question, often privileging one expression or the other the biological or the biographical. But is it possible to conceive of them together and thus reconcile naturalist and humanist approaches? DF, Life: A Critical User’s Manual, “Acknowledgments” While validating this theory, the discovery of the DNA double helix a few years later constituted the foundation for a new conception of life, now based on information and its replication. Fifty years later, the recent decoding of the human genome has further refined this concept. https://luckycodes.netlify.app/life-a-critical-users-manual.html. Apr 26, 2019 Life: A Critical User's Manual Didier Fassin on Amazon.com.FREE. shipping on qualifying offers. How can we think of life in its dual expression, matter and experience, the living and the lived?

requirements of the local authority having jurisdiction.

Testing should be done as a minimum as described below

1. Notify the fire department or other receiving station if alarm, supervisory and/or trouble signals are transmitted.

2. Notify the proper building personnel so that audible and/or visual signals can be ignored.

3. If the release panel is monitored by a building fire alarm panel, take appropriate action to eliminate any unwanted events.

4. Momentarily open each of the following circuits.

Each initiating device zone

•

Supervisory circuit

•

Notification Appliance/Releasing circuit - observe that this results in a trouble condition and all indicators operate as

•

described in the appropriate preceding section for the particular circuit that is faulted.

RED OUTPUT LED STEADY: ABORT

ZONE 1

ZONE 2

ZONE 3

ZONE 4

OUTPUT 1

OUTPUT 2

OUTPUT 3

Fire Alarm Annunciator Panel Location

OUTPUT 4

AC POWER

POWER TBL

SYSTEM TBL

SUP TBL

GROUND FAULT

SUP 1/ABORT

SUPERVISORY 2

COMMON ALARM

ALARM SILENCE

STEADY: DISCHARGING

FLASHING: PRE-DISCHARGE

LAMP TEST

SILENCE

DWG# 3550-17

Advertising

Popular Brands

Popular manuals

Advertising

P/N 151042 Rev C

ECN 14-0358

5860 Remote Fire Annunciator
Installation Quick Reference

The optional Model 5860 Remote Annunciator, as shown
in Figure 1, can be surface or flush mounted.

Fire Alarm Annunciator Panel Definition

Figure 1: Model 5860 Remote Annunciator

5860 installation involves the following steps:

Make sure power is off at the panel.

Annunciator is assembled at the factory. Disassemble
as needed.

Mount annunciator.

Wire annunciator to the panel. See

Use the DIP switches on the back of the 5860 to set
the annunciator ID. See Figure 4.

Figure 2: 5860 Parts

Wiring Connections

Wire the 5860 to the FACP as Shown in Figure 3.

Figure 3: SBUS Connections

Figure 4: DIP Switch settings

Product